Scrum Master Resume
SUMMARY:
7.5 years of work experience in Design, Development, Verification & Validation, Testing, Qualification of Product, Project Lead, Project Management, Procurement of raw material and Scrum Master. Skilled in Analog, Digital and High - speed circuits in Electrical Electronics products make me confident seeking a challenging position in a company.
TECHNICAL SKILLS:
Schematic Tools: Altium Designer, ORCAD Capture & Allegro, PADS, Mentor Graphics Dx Designer & Hyperlynx.
Hardware Design: Analog, Digital, High Speed, AC-DC, DC-DC, Low Power, LDO, Linear Regulator.
Interfaces: Differential lines, PCI, SPI, I2C, I2S, RS232, RS422, Ethernet, Parallel bus, USB, UART, GPS.
Equipment: Oscilloscope, E-Load, logic Analyzer, Power Analyzer, Signal Analyzer, Generators, Multimeter.
Industries: Automotive, Aerospace, Consumer Electronics, Industrial Automation, Manufacturing.
Programming Acquaintance: Ability to read & perceive Existing code in C/C++, VHDL, Verilog.
Standards Exposure: Familiar with BSEE, IEEE, UL Stds and respective Internal company quality STDs.
Documentation: PRD, PDR, FRS, HLDD, DDD, FMEAs, TS, TR, QTP, EMI-EMC, ENV, UM, SIP, Datasheet.
EMI/EMC: ESD, Conducted Immunity, Radiated Immunity, Radiated Emissions, CE, Surge, EFT, etc.
Environment: al Tests Shock & Vibration, Drop test, Stress Test, Temperature, Thermal Cycling.
PROFESSIONAL EXPERIENCE:
Confidential
Scrum MasterResponsibilities:
- Good at checking the Feasibility of different ways of doing form ideas generation to Release.
- Familiar with engineering design process and product life cycle.
- Developed in different types of Analog Sensors signal conditioner modules like Strain, Pressure, Ultrasonic, vibration, acceleration, Potentiometer, Flow rate, Temperature using FPGA & SOC based boards etc.
- Designed various digital boards with Microprocessors, Microcontrollers of different Vendors like Microchip, Renesas, Texas Instruments, ST Microelectronics, and Silicon Labs.
- Development of Power Management solutions such as DC to DC Converters, Low Drop out Regulators, Linear Regulators, Battery Management, Motor driving control system.
- Components Selection, Block diagram, Schematics Preparation, Bill of Material Finalization.
- Experience in doing Electrical Wiring diagrams such as Electrical Integration Architecture.
- Experience in Multiple interfaces like DDR, SDRAM, SRAM, Flash, RS 232/422/485.
- Development of motor drives, inverters, SMPS, AC to DC Converters and DC to DC Converters, LDO’s, Linear Regulators.
- Experience in test setups, test equipment maintenance, support, inventory, procurement.
- Familiar with engineering design process and defining Product hardware Architecture.
- Understanding of Basic Firmware and ability to understand existing code and modify it.
- Knowledge on Inertial Navigation systems (INS), GPS & Inertial Measurement Unit (IMU).
- Knowledge on Programmable logic controllers (PLC’s), Analog, Digital Inputs & Output (IO) Modules, Relay Output Modules, LAN Modules, Ethernet devices etc.
Confidential
Scrum MasterResponsibilities:
- Hands on Experience in Power budget Calculations, Thermal & Heat dissipation Analysis.
- Expertise in doing simulations for Analog & Power Electronics circuits.
- Experience with PCB layout oversight using Allegro.
- Knowledge in High-speed design, Noise suppression techniques.
- Expertise in execution of Electrical Design Verification Test cases.
- Good electrical measurement techniques.
- Excellent debug skills of board and test set-up issues.
- Ability to provide innovative test solutions and fixtures.
- Take the product through development, compliance testing, operator testing, ramp up and sustaining.
- Experience with Technical document writing using Visio, Word, Excel, and / or PowerPoint.
- Experience with Revision and Document control.
Confidential
Team LeadResponsibilities:
- Experience in doing in circuit Test, Board brings up, Functional Test, and Board level Tests.
- Ability to provide innovative test solutions and fixtures.
- Works with other functional teams to Investigate root cause issues and find solutions.
- Experience in EMI/EMC Tests, Vibration, Acceleration, Shock, Thermal Cycling, High Temperature, Low Temperature, Pressure, Rain, Tropical, High Altitude, Sand & Dust, Bump.
- Validated hardware and software in hostile environments by performing environmental tests.
- Share the ideas with different suppliers on various design approaches.
- Exchange the information with seniors and management to approvals for various stages.
- Works with Software team to develop the Graphical user interface platform.
- Communicate with Firmware team to write the Programming for the main controller in the board.
- Co-ordinate with Procurement team on purchasing the components.
- Synchronize with PCB Engineer on Placement, Layout, Layer Stack up and Routing.
- Correlate with Mechanical Engineer on Product Dimensions and Arrangement of Connectors.
- Collaborates with Management, Product Marketing, Planning, Quality, regarding project progress.
Production/Manufacturing support
Confidential
Responsibilities:
- Develop and maintain instrument/subsystem test station for production.
- Expertise in soldering skills for board/test set-up modifications.
- Guide Technicians on through hole Component Soldering, Potting and Conformal coating for PCB Assembly and wiring and Involved on Manufacturing Process and Familiar with Confidential & Non Confidential Process.
- Knowledge on Stencil usage, Apply Solder paste on bare PCB’s, Programming to SMT machine regarding component locations on PCB, arrange components Confidential & Trays respective to machine, Components Assembly, Maintain required Temperature.
- As a Team Lead managed the project from ideas generation to production.
- As a Scrum Master Co-ordinated Daily stand-up meeting & Sprint Project Planning with others.
- Preparation of Hardware requirement specification and High-level design document.
- Schematic Capture & Layout using ORCAD, Dx Designer, Zuken and Altium.
- Component Selection and BOM Preparation.
- Design Analysis I.e., Power Analysis and Placement analysis.